| Tittel: | HAMILTON STANDARD ENGINE ELECTRONICK CONTROL - COMPONENT MAINTENANCE MANUAL WITH IPL 73-21-13/SERVICE BULLETIN ENGINE FUEL AND CONTROL EEC118-11-73-XX : and FUEL CONTROL COMPONENT MAINTENANCE MANUAL WITH IPL 73-21-41/SERVICE BULLETIN ENGINE FUEL AND CONTROL JFC118-11-73-XX | | Materialtype: | Manual/Sivil | | Signatur: | 20-B-5 | | Utgitt: | Ontario : Hamilton Standard | | Emneord: | Component maintenance manual / Engine electronic control / Illustrated parts list / Service Bulletin | | Materialbetegnelse: | Technical Handbook | | Materialbetegnelse: | Perm | | Note: | There are 4 individual manuals in this binder. The first one is published Oct 15/83.
Last Revision; Revision No. 4, Issue Date: February 15/93.
The second one has no publishing date.
The third one is published April 1/85, Last Revision; Revision No. 2
Issue Date: Aug 15/91.
And the fourth has no publishing date. | | Innhold: | TABLE OF CONTENTS:
(ENGINE ELECTRONIC CONTROL, CMM WITH IPL)
INTRODUCTION
Scope
Arrangement of Manual and Usage
Description and Operation
Testing and Troubleshooting
Disassembly, Cleaning, Check, Repair, and Assembly
Illustrated Parts List
Leading Particulars
Cooling
Physical Dimensions
Power Input Requirements
Verification
Nameplate
Abbreviations
DESCRIPTION AND OPERATIONS
System Description
EEC Physical Description
EEC Operation
Input Conditioners
DC Voltage Inputs
General
Reference Protection Voltages
Potentiometer Excitation
PLA Potentiometer Signal
PO Ambient Pressure Signal
PO Sensor Bias (Zero Calibration) and Gain (Full Scale Calibration) Compensation
^P Differential Pressure Signal
^P Sensor, Bias (Zero Calibration) and Gain (Full Scale ^P Calibration)
Compensation
TO Ambient Temperature Signal
Drift Signals
Q Bug Reference Input
Torque Motor Current Sense
A/D Converter
A/D Conversion
Speed Inputs
General
NH Speed Measurment
NPT Speed Measurment
Discrete Inputs
General
Engine Trim/Test Trim (1-3)
Rating Trim (1 and 2)/Test Trim (4 and 5)
Ground Test
Take-off
Reduce Power
Rating Logic Bits (1 and 2)
NH Overspeed Test
Reversion Mode
Arm Propeller Governor
Uptrim
Feather
Microprocessor
General
Data Bus Buffers
Programmable Read Only Memory (PROM)
Random Access Memory (RAM)
Control Multiplexer
NH Overspeed Detector
NH Underspeed Detector
Output Interface
Torque Motor Output
High Side Switch
Torque Meter Bug Output
EEC Fault Indicator Output
Reversion Mode Relay Output
Serial Display
Built-In-Test
General
PROM Sum Check
RAM Test
Foreground/Background Health Test
Interface Flag Check
Instruction Test
Range Test
Test Voltage
Watchdog Timer
Loss of Clock Detector
Power Supply
General Operation
Power Input and Effector Supply
Pulse Width Regulation
Protection Circuits
+5V Overvoltage
+28V Undervoltage
Transformer Overcurrent
+12V Supplay
-12V Supplay
+5V Supplay
PSR Generator
Microcircuits
TESTING AND TROUBLESHOOTING
Introduction
Functional Bench Test
General
Required Equipment
Signal Definitions
Input Signals
RAM Address Signals
Output Signals
Test Procedures
Initial Conditions
Preliminary Tests
Input Power
EEC Current Check
Correction Factor (C. F.)
RAM Readout Check
Funcitonal Test
Thermal Cycle Test
General
Required Test Equipment
Signal Definitions
Input Signals
Output Signals
Test Procedures
Vibration Test
General
Required Test Equipment
Signal Definitions
Input Signals
Output Signals
Test Procedures
Troubleshooting
General Information
Reversion and Fault Flag Decode
Maintenance Word
Schematic References
Digital Microcircuit References
DISASSEMBLY
General
Disassembly
Cover Removal
Digital Board Assembly Removal
Analog Board Assembly Removal
Pressure Transducer Removal
Connector Module Removal
CLEANING
General
External Cleaning
Internal Cleaning
CHECK
General
Visually Inspect Board Assembly
Visually Inspect Chassis and Mechanical Assemblies
REPAIR-GENERAL
General
Materials and Tools
ASSEMBLY
General
Assembly
J1 Connector Module Installation
Pressure Transducer Installation
Analog Board Assembly Installation
Digital Board Assembly Installation
Storage Instructions
End Assembly
Subassemblies and Components
FITS AND CLEARANCES
General
SPECIAL TOOLS, FIXTURES AND EQUIPMENT
General
ILLUSTRATED PARTS LIST
Introduction
Purpose
Configuration Control
Item Number and Variants in the Detailed Parts List
Configuration Changes Codes
Configuration Changes Summary
Parts Listing Procedures
Part Numbers
Effectivity Codes
Abbreviations and Symbols
Electrical/Electronic Component Parts List
Using an Electrical/Electronic Component Parts List
Electronics Parts Wich Require Special Handling
Provisioning Parts List Procedures
Identification of Current Parts List Changes
Material Information Table
Vendor Codes
Equipment Designator Index
Numerical Index
Detailed Parts List
Figure 1 - Engine Electronic Control
Figure 2 - Digital Board Assembly
Figure 3 - Digital Board Assembly, Component Side
Figure 4 - Digital Board Assembly, Solder Side
Figure 5 - Analog Board Assembly
Figure 6 - Analog Board Assembly, Component Side
Figure 7 - High Side Switch Board Assembly
Configuration Change Summary
NO. 2 HAS NO TABLE OF CONTENTS
FUEL CONTROL, CMM WITH IPL
Introduction
Description and Operation
Description
Operation
Testing and Troubleshooting
Test Conditions
Symbols and Abbreviations
Required Equipment
Preparation of Fuel Control for Test
Preliminary Control Setup and Adjustment
Final Calibration and Recording of Test Data
Post Test Requirements
Troubleshooting - Control Calibration
Disassembly
General Instructions
Turbine Type Engine Fuel Control
Application Housing Group
Main Housing Group, Part 1
Main Housing Group, Part 2
Main Housing Group, Part 3
Application Housing and Inserts
Housing and Valve
Cleaning
General Cleaning Requirements
Specific Cleaning Requirements
Check
General Requirements
Nondestructive Test Data
Repair-General
General
Steel Parts
Aluminum Parts
Rubber Parts
Dowel-Type Straight Pins
Screw Thread Inserts
Woodruff Keys
Specific Repair
Assembly
General Assembly Procedures
Housing and Valve
Application Housing and Inserts
Main Housing Group, Part 3
Main Housing Group, Part 2
Main Housing Group, Part 1
Application Housing Group
Turbin Type Engine Fuel Control
Storage After Assembly
Fits and Clearances
Sliding Fits
Springs
Assembly Torque Valves
Special Tools, Fixtures and Equipment
Illustrated Parts List
NO. 4 HAS NO TABLE OF CONTENTS | | Eier: | Norsk Luftfartsmuseum | | |
|
| 1.ex | Ikke til utlån | | Norsk Luftfartsmuseum | Norsk Luftfartsmuseum | | | |
|
|