| Tittel: | FIGHTING FALCON POWER HANDBOOK : F-16/F100 Maintenance Awareness Program |
| Forfatter: | Maintenance Awareness Program (ms D-21) |
| Materialtype: | Manual/Sivil |
| Signatur: | 20-C-4 |
| Utgitt: | West Palm Beach, FL : Pratt & Whitney, 1983 |
| Omfang: | viii, 153 s. - ill. |
| Klassenummer: | 629.134 |
| Emneord: | F100 Motor / F-16 Skrog / General Dynamics / Pratt & Whitney |
| Materialbetegnelse: | Spiralhefte |
| Materialbetegnelse: | Technical Handbook |
| Lokal Note (gave): | Reidun Størkesen ; fra Ole Størkesens etterlatte papirer |
| Note: | Published 1983, No Revisions |
| Innhold: | TABLE OF CONTENTS:
Preface
SECTION I ENGINE DESCRIPTION
Engine Description
High-Pressure-Ratio Design
Modular Construction
Inlet Fan Modul
Core Modul
Fan-drive Turbine Modul
Augmentor and Exhaust Nozzle Modul
Gearbok Modul
Fan Ducts (Outer)
Primary Control System
Unified Control
Engine Electronic Control
Backup Control System
BUC Specifications
Variables During BUC Operation
Variable Geomentry Transfer Valve
Engine Ignition System
Engine Interconnecting Box
Events History Recorder
Importance of Accurately Recording EHR Data
Component Failure Diagnostic Provision
Fuel Filter Assembly
Derich System Fuel Filter
SECTION II ENGINE-AIRFRAME INTERFACES
Engine-Airframe Interfaces
Engine Inlet and Duct Configuration
Engine Anti-Ice System
Engine Mount System
Bleed Air for the Airframe
Central Air Data Computer
Cockpit Instruments and Indicators
FTIT Indication System
Nozzle Position Indication System
Fuel Flow Indication System
Oil Pressure Indication System
Cockpit Lights
Cockpit Voice Warning/Caution System
Access to Engine Components
Throttle Control System
Low Oil Pressure Switch
Engine Starting System
Support
System Operation Overview
ESS Specification
Controller
Hydraulic Start Motor
Accessory Drive Gearbox
Power Takeoff Shaft
Jet Fuel Starter
SECTION III INSTALLED ENGINE GROUND OPERATIONS
Engine Start
Ground Idle Operation
Operating in Icing Condition
Typical Engine Ground Operating Characteristics
Exhaust Nozzle Position
Trimming the F100
EEC Closed-loop Idle Check
RCVV Schedule Trim and Check
CIVV Schedule Check
UC Idle Trim (EEC Off)
UC FTIT Trim
EEC Trim
Thrust Parameter Check
A/B Fuel Flow Trim (Wft/Pb)
UC and EEC Trim Adjustments
SECTION IV PROPULSION SYSTEM SERVICING
Engine Oil System Servicing
Oil Sight Cauge Scale
Oil Tank Sight Gauge Readability
ADG Servicing
SECTION V TROUBLESHOOTING
JFS Compressor Inlet Temperature Sensor
PTO Speed sensor Connection
JFS Thermal Damage Prevention
Hung Start
Hot Start
Engine Oscillations
A/B No-lights and Blowouts
How to Recognize a No-light or Blowout
A/B No-lights and Blowouts on Takeoff
A/B Operating Envelope
Segment 5 Lockout Improves ULHC A/B Operation
Oil Consumption
EEC Light
Stall
Types of Stall
Mechanics of a Stall
Reacting to Stalls
Reacting to Stagnations
Trimming
Trim Functions
Trimming Errors
F100 Trim Check Guidelines
Fan Knife-Edge Seals
SECTION VI MAINTENANCE TIPS
Unexplained Oil Leakage Into the JFS Intake Duct
JFS Start Limit
Engine Removal and Installation
Main Fuel Inlet Manifold
Throttle Coupling
PTO Shaft
Interconnecting Box Electrical Connectors
Drain Bellows
A Missing Dogbone
RCVV System Looseness
New RCVV Bellcrank Arms
4th Stage Turbine Airseal Bolts
Critical Electrical Connections
Nozzle Burntrough
Fuel and Oil Leaks/Plumbing
Excessive FTIT Spread
Ignitor Plugs
Stuck FTIT Probes
Chafing (No. 5 Bearing Scavenge Tube/Stepper and Solenoid Special Purpose Cable)
Fan Duct Bracket Attaching Hardware, Pins and Collars (Parts Substitution)
Compressor Disk and Hub Cover (Missing Key Washer Slot)
Core Rejection (Sealant on Airfoils Misinterpreted an Fod)
Segment 1 Spray Manifold Installation
Maintenance Hazard Analysis
F100 Engine Warranty Program
SECTION VII THE TOOLS OF OUR TRADE
Technical Order
Ignition Test Set (PWA 50025)
Mach Number Simulator (PWA 50037)
Engine Trim Box (PWA 50081)
Supervisory Control System Test Set (PWA 50105)
PWA 51932 Heather
PWA 51949 Wrench
PWA 51014 Pusher
PWA 25672 Heather Control
PWA 50308 Wrench
Enhanced Horizontal Maintenance Capability (JEIM)
Engine Derich Timer Relay Test Adapter
Oil Drain/Breather Retractor
ADG Adapter Assembly
Seal Driver
Rail Aligning Fixtures
Protective Throttle Cover
Adapter Assembly (Engine Installation)
Mechanical Force Gauge
Tank and Pump Unit
Engine Transportation Trailer (Model 3000)
Wrench Adapter (Gland Air Inlet Door Actuator)
Depth and Shimming Gauges
Combustor Puller (JFS)
Electronic Componet Tester (ESS)
Engine Screen Assembly (Anti-Personnel)
Inlet Ice Dolly
Inspection
Use of Ice Dolly
F100 Engine Complex Age Information
Pacer Wrench Program
SECTION VIII PERSONNEL SAFETY
Danger Areas
Uncontained JFS Turbine Wheel Failures
SECTION IX GLOSSARY
Acronyms and Abbreviations |
| Eier: | Norsk Luftfartsmuseum |
| |
|