| Tittel: | INSTALLATION MANUAL : Electrothermal Propeller De-Icing Systems | | Materialtype: | Manual/Sivil | | Signatur: | 24-D-5G | | Utgitt: | The BFGoodrich Company, 1978 | | Omfang: | 49 s. - ill. | | Serie: | Report No. ; 70-04-700C  | | Emneord: | BFGoodrich / De-Icing / Hartzell Propeller / Installation / Manual / Propeller | | Materialbetegnelse: | Technical Handbook | | Materialbetegnelse: | Hefte | | Note: | Published APRIL 1, 1978. | | Innhold: | TABLE OF CONTENTS (MAIN SECTIONS):
SECTION 1: INTRODUCTION
1-1 How to Use This Manual
1-2 Applicable Regulations
1-3 Maintenance Instructions
SECTION 2: DESCRIPTION
2-1 Description of Installation
2-2 De-Icing Systems
2-3 Principles of Operation
2-4 Description of Components
SECTION 3: ELECTRICAL LOAD REQUIREMENTS
3-1 Required Electrical Capacity
3-2 Limitations
SECTION 4: WEIGHT AND BALANCE
4-1 General
SECTION 5: REMOVAL AND MODIFICATION OF AIRCRAFT COMPONENTS
5-1 General
5-2 Removal of Component
5-3 Modifications of Aircraft Components
SECTION 6: PROPELLER DE-ICER INSTALLATION
6-1 General
6-2 Sealing of Propeller De-Icer and Lead Strap
6-3 Balance Weights
6-4 Lead Strap Clamps or Restrainers
6-5 Rubber Restrainer Strap Installation
6-6 Modifying Hartzell Compact Propellers
SECTION 7: TIMER INSTALLATION
7-1 General
7-2 Installations Methods
SECTION 8: AMMETER, SWITCH AND CIRCUIT BREAKER INSTALLATION
8-1 General
8-2 Ammeter Installation
8-3 Switch (or Circuit Breaker/Switch) Installation
8-4 Warning Placard Installation
8-5 Circuit Breaker Installation
SECTION 9: INSTALLATION OF STARTER RING GEAR/SLIP RING ASSEMBLY AND PROPELLER
9-1 General
9-2 Spinner Adapter Ring Modification and Installation
9-3 Spinner Bulkhead Modification
9-4 Installation of Starter Ring Gear/Slip Ring Assembly and Propeller
9-5 Propeller De-Icer Wiring
9-6 Alignment of Starter Ring Gear/Slip Ring
SECTION 10: INSTALLATION OF SLIP RING ASSEMBLY AND PROPELLER
10-1 General
10-2 Modification of Spinner Bulkhead
10-3 Installation of Hardware on Modified of Spinner Bulkhead
10-4 Installtion of Slip Ring Assembly, Spinner Bulkhead and Propeller
10-5 Propeller De-Icer Wiring
10-6 Alignment of Slip Ring Assembly
SECTION 11: BRUSH BLOCK ASSEMBLY INSTALLATION AND ALIGNMENT
11-1 Installation
11-2 Alignment Requirements
11-3 Adjustment Methods
SECTION 12: WIRING
12-1 General Information
12-2 General Precautions
12-3 Timer
12-4 Ammeter (If Used)
12-5 Switch or Circuit Breaker/Switch
12-6 Circuit Breaker (If Used)
12-7 Fuselage
12-8 Firewall Connector
12-9 Firewall to Brush Block Assembly
12-10 Brush Block Assembly
SECTION 13: INSPECTION AND TESTING
13-1 General
13-2 Slip Ring Run-Out Test
13-3 Brush Block Assembly
13-4 Propeller De-Icer Resistance Check
13-5 Timer Test
13-6 Propeller De-Icer Heat Test
13-7 Continuity of Wiring Check
SECTION 14: POST INSTALLATION PROCEDURE
14-1 General | | Fortsettelse av: | | | Fortsettelse som: | | | Eier: | Norsk Luftfartsmuseum | | |
|
| 1.ex | Ikke til utlån | | Norsk Luftfartsmuseum | Norsk Luftfartsmuseum | | | |
|
|